Aluminum Extrusion Services with Custom Machining and Finishing

Aluminum extrusion pushes heated aluminum through a shaped die to create a profile with a consistent cross-section along its length. It is useful for rails, frames, channels and other parts built around a repeated section. Aluminum extrusions are produced with qualified partner factories; KM Rapid handles DFM review, project management, quality inspection and delivery. Any machining and finishing required for the finished component are coordinated within the agreed scope.

Aluminum extrusion housings and panels produced by our partner factory.

Service Capabilities

SpecificationCapability
Materials6000-series aluminum alloys (such as 6061 and 6063); alloy and temper confirmed at quotation
ProfilesCustom profiles from your drawing; standard and custom dies
Size, wall thickness and toleranceDepend on profile design and alloy; confirmed at quotation from your drawing
Secondary operationsCan be combined with CNC machining, cutting to length, anodizing, powder coating and other finishes
QualityIncoming inspection by KM Rapid before delivery
NDAAvailable
PricingQuoted from your drawing (profile, alloy, length, quantity and finish)

The profile and finished part drawing serve different purposes. Supply both where available, showing which features come from the extruded section and which are added afterward. This makes it easier to review the complete manufacturing route and avoid treating every hole or pocket as part of the extrusion die.

Alloy, Temper and Finish

Specify the required aluminum alloy and temper, together with the part’s structural, appearance or environmental requirements. The material condition and subsequent operations should be considered together. Exact grades and availability are reviewed for the enquiry. If anodizing is required, describe the appearance and functional surfaces so material selection, machining and surface preparation can be assessed as a combined requirement.

When to Choose This Process

Choose extrusion when a repeated cross-section is central to the design and the profile can be used across the required finished lengths. Rails, channels and enclosure sections are typical applications. Machining can add local features after extrusion. For an early design trial, machining from stock may allow evaluation before a custom die is made.

How Your Project Moves Forward

Share the profile

Provide the cross-section, finished part model, drawing, quantity and intended application. Identify mating interfaces and visible faces.

Review the route

KM Rapid reviews the profile with the production partner and coordinates requirements for machining, finish and inspection before quotation.

Coordinate production

The partner manufacturer produces the profile. KM Rapid follows progress and coordinates the agreed downstream work and drawing revisions.

Inspect and deliver

Incoming inspection follows the agreed requirements. Packing and delivery are arranged for the finished parts, with any special handling discussed during review.

Design and Drawing Review

Think about the profile as a complete section rather than a collection of separate walls. Abrupt thickness changes and difficult internal shapes can affect material flow and tooling. Identify straightness, fit and appearance requirements on the drawing without assuming that a general profile specification covers the finished assembly. Features positioned along the length should have clear references for later machining.

Machining, Finishing and Delivery

Local holes, pockets and connection features can be assigned to CNC machining after the profile is produced. State whether visible faces are to remain untouched or receive a finish. Anodizing and other finishes must suit the substrate and application. KM Rapid coordinates these operations within the agreed project scope, including any assembly requirements that need review.

Compare Manufacturing Routes

ProcessWhen it fitsWhat to review
Aluminum extrusionRails and sections with a repeated cross-sectionA custom section requires die and material-flow review
CNC machiningLocal features and evolving part designsUseful for secondary details or a prototype from stock
Sheet metal fabricationPanels and folded enclosuresUses bends and joining rather than an extruded section

See CNC machining for secondary features and surface finishing for anodizing and other options.

Frequently Asked Questions

Can’t find your answer? Talk to our engineers.

  • Does KM Rapid extrude the profiles in its own factory?

    Partner manufacturers carry out the extrusion. KM Rapid manages DFM review, quotation, project follow-up, incoming inspection and delivery.

  • Can you supply machined and finished profiles?

    KM Rapid can coordinate CNC machining and finishing as part of an extrusion project. Supply the finished part drawing, material requirement and desired surface condition so holes, pockets, masking and inspection needs can be reviewed together.

  • Should I send a profile drawing or a finished part model?

    Send both when available. The section drawing explains the extruded shape, while the finished part model and drawing show length, local features and interfaces. Include the intended application and quantity to help the team assess the manufacturing route.

Ready to Start Your Project?

Send your CAD model, drawing, material and quantity. Our engineers will review the manufacturing route and quotation.